Two Notes Reload II Load Box And Attenuator

MUSICTONER presents the Two Notes Reload II Load Box And Attenuator. Introducing Torpedo Reload II. The latest instalment in Two notes’ class-leading reactive load solution legacy marking the definitive watershed in contemporary backline control. Featuring twin-channel operation, selectable multi-impedance compatibility and true continuous attenuation, Reload II is our most advanced Load Box to date. Its mission is simple: unleash the power of any amplifier or line-level source without compromise. Armed with a ground-up rework of our defining reactive load for a Celestion® Approved Load Response, the match is set to drive any amp’s power-stage (rated up-to 200W RMS) to perfection, retaining all the sonic integrity your performance demands. Scalable from a whisper to a full-throttle onslaught, Reload II’s ultra-transparent dual-mono 215W (per channel) amplifier/attenuator and paired speaker outputs preserve every facet of your tone. Add a Stereo FX Loop, dual Line outputs and GENOME Reload I! Edition (software download) into the mix and Reload MKII doesn't just enhance your rig, it redefines it. Speaker Input Jack 6.35mm (1/4”) unbalanced (TS, Tip/Sleeve) Maximum input Voltage: 140V AC (45dBu) Max Security Load: 270Ω / 20W Load Input Level Adjustable via potentiometer with continuous attenuation (-inf) to continuous amplification (+20dB) Speaker Outputs (2) Jack 6.35 mm (1/4”) unbalanced (TS) Min Load: 3.5Ω Max Output Power (single channel at THD+N <1%): 1x 215 W RMS @ 4Ω 1x 120 W RMS @ 8Ω 1x 50W RMS @ 16Ω Maximum Output Power (both channels driven at THD+N <1%): 1x 215 W RMS @ 4Ω 1x 120 W RMS @ 8Ω 1x 50W RMS @ 16Ω Line Inputs Dual-Mono, (2) Jack 6.35mm (1/4”) balanced (TRS, Tip/Ring/Sleeve) Switched jacks for routing to an unplugged channel Impedance: 300Ω Gain (In to Out): +4 to -inf dB Maximum Output Level: 20dBu Noise: Under -99dBu from 20Hz to 20kHz Frequency Response @ -1dB: 20Hz to 20kHz FX Loop Dual-Mono Fx loop with independent CHANNEL A and CHANNELB controls (2) SEND + (2) RETURN via 6.35mm (1/4”) unbalanced (TS) Jack Compatibility with +4dBu and -10dBV devices, selectable via a dedicated switch per channel DRY/WET potentiometer with ON/OFF switch Facilities to Copy CHANNEL A return to CHANNEL B output via dedicated switch FX loop activation/deactivation via Footswitch with a 6.35mm (1/4”) Jack; (TRS, Tip/Ring/Sleeve) or (TS, Tip/Sleeve) compatible and configurable via a dedicated Footswitch behaviour switch Load Box Reactive Load featuring a Celestion Approved Load Response with nominal impedance: 4- or 8- or 16-Ohms (switchable) Maximum Admissible Power 200W RMS (assuming proper ventilation) Maximum Temporary Admissible Power 250W peak (assuming proper ventilation) Tone Control (1) DEPTH and (1) PRESENCE control per CHANNEL Flat response on potentiometers at 0% (1) MOJO control per CHANNEL to deliver high-power feel at low volume Depth: +8dB @75Hz on potentiometer at 100% Presence: +8dB @4kHz on potentiometer at 100% Cooling Passive cooling with amplifier heatsink and Load Box heatsink Active cooling with temperature-controlled fan with 2 speeds (Slow & Boost) Thermal Security To prevent damage to the internal Load Box, thermal cut off is implemented when the internal temperature rises over a predesignated threshold. When active, a 270Ω security load is placed into effect and the signal is muted Power Supply Type: IEC60320 C14 power connector Input Voltage: Compatible with 100V – 230V @ 50- to 60Hz Power: 100W Max Dimensions & weight Width x Depth x Height*: 365mm x 89mm x 220mm 365mm x 89mm x 240mm Including connectors and knobs Product condition: New.